Soldering for the First Time | Ask This Old House
ADVERTISMENT – become one of us and contribute knowledge
You Might Be Interested In
Comment (0)
LEAVE YOUR COMMENT
You must be logged in to post a comment.
WEB EXCLUSIVE: In a recent episode of Ask This Old House, plumbing and heating expert Richard Trethewey helped landscape designer Jenn Nawada hook up a fridge with an icemaker. While he was there, he offered Jenn a crash course on soldering.
SUBSCRIBE to This Old House: http://bit.ly/SubscribeThisOldHouse
Time: 1 hour
Cost: $50
Skill Level: Moderate
Tools List for Soldering:
Measuring tape
Pipe cutter
Blow torch
Bucket
Shopping List:
Pipe cleaner
Solder
Flux
Pipes
Fittings
Rags
Steps:
1. Shut the water off to the pipes being soldered.
2. Measure and cut the pipes to length using the pipe cutter. Have a bucket ready to catch any water left over in the pipe.
3. Let the pipes dry before soldering or the connection won’t take.
4. Use a pipe cleaner to clean the outside of the pipes and the insides of the fittings.
5. Generously apply flux to the cleaned ends of the pipes and fittings and fit the pieces together.
6. Hold the blow torch on the opposite side of where you plan to apply to solder. Wait a few minutes to allow the pipe to heat up, and then gently touch the pipe with the solder. If it quickly wraps around the entire connection, then it took properly. If it did not, continue to heat the pipe up and try again.
7. Wipe down the excess solder on the pipe with a rag.
8. Turn the water back on.
Resources:
All the materials required for soldering – solder, flux, blow torch, pipes, and fittings – are available at home centers and plumbing supply houses.
About Ask This Old House TV:
Homeowners have a virtual truckload of questions for us on smaller projects, and we’re ready to answer. Ask This Old House solves the steady stream of home improvement problems faced by our viewers—and we make house calls! Ask This Old House features some familiar faces from This Old House, including Kevin O’Connor, general contractor Tom Silva, plumbing and heating expert Richard Trethewey, and landscape contractor Roger Cook.
Follow This Old House and Ask This Old House:
Facebook: http://bit.ly/ThisOldHouseFB
Twitter: http://bit.ly/ThisOldHouseTwitter
http://bit.ly/AskTOHTwitter
Pinterest: http://bit.ly/ThisOldHousePinterest
Instagram: http://bit.ly/ThisOldHouseIG
http://bit.ly/AskTOHIG
Tumblr: http://bit.ly/ThisOldHouseTumblr
For more on This Old House and Ask This Old House, visit us at: http://bit.ly/ThisOldHouseWebsite
Soldering for the First Time | Ask This Old House
https://www.youtube.com/user/thisoldhouse/
You must be logged in to post a comment.
This site uses Akismet to reduce spam. Learn how your comment data is processed.
Looks very easy but takes a little practice. Lots of people comment on deburring. I'd suggest MAP gas and moving the flame over one side of the fitting. Tinning flux is probably a better choice for most. It usually takes a length of solder about equal to the pipe diameter, so I bend the rod at 1/2" for 1/2" pipe as a guide. Apply the solder opposite the heat source and lower on the fitting so that, when you see the solder on the heated side, you know that capillary action has filled the joint rather than gravity moving it over flux. Then wipe it down.
Where permitted, use 50-50 lead solder since it has a lower melting point and is therefore easier to use.
Obviously must not be used on pipes for potable water. Pex, compression fittings, etc. are very popular for good reasons.
I turn the pipe cutter but she turned the copper lol
I just came to see if her first solder joint is as bad as mine was. I had dabs of solder and burnt flux all over the place
not a smart move the solder over a nice hardwood floor
I applaud her effort but that was painful to watch.
Stay in the groove baby
My first time soldering I was surprised how easy it was. I'm sure larger pipe 1 1/2" and above is a different story
major misstep! forgot to debur the inside of cut pipe. without doing this will cause the joint to fail
Richard looks like he's teaching her while sleeping… he's a pro