How to Install a Solid-Wood Exterior Door | Ask This Old House
ADVERTISMENT – become one of us and contribute knowledge
You Might Be Interested In
Comment (0)
LEAVE YOUR COMMENT
You must be logged in to post a comment.
General contractor Tom Silva helps a homeowner install a new, energy-efficient wood door. (See below for a shopping list, tools, and steps.)
SUBSCRIBE to This Old House: http://bit.ly/SubscribeThisOldHouse
Shopping List for How to Install a Solid-Wood Exterior Door:
Pre-hung wood entry door [https://amzn.to/2O3BvTd]
Minimal-expansion insulating foam [https://amzn.to/34HJDie], to seal cracks and voids
Exterior-grade acrylic-latex caulk [https://amzn.to/2O1DXcQ], to seal threshold
2 1/2-inch nails for pneumatic nailer [https://amzn.to/2NXvjfo]
Wood shims [https://amzn.to/2NWOWo1], to shim the doorframe
3-inch decking screws [https://amzn.to/2O1E4oM], to fasten doorjamb to framing
Fiberglass insulation [https://amzn.to/34Jbv5y], to fill large voids
Tools List for How to Install a Solid-Wood Exterior Door:
Hammer [https://amzn.to/32FNivf]
Slotted screwdriver [https://amzn.to/2NZCmEs]
Utility knife [https://amzn.to/31dHcSq]
Flat bar [https://amzn.to/2ZUuV81], for prying off casings
Reciprocating saw [https://amzn.to/2LqtLZM], to cut through nails
Level [https://amzn.to/2ZLPXpd]
Caulk gun [https://amzn.to/2Lorz4S]
Pneumatic nailer [https://amzn.to/2LrKbAY] and air compressor [https://amzn.to/2Lsq0Dj]
Cordless drill [https://amzn.to/2LrY6Y6]
Impact driver [https://amzn.to/2LraKFj]
Steps for How to Install a Solid-Wood Exterior Door:
1. Tap out the hinge pins from the old door using a hammer and a slotted screwdriver. Remove the door.
2. Use a utility knife to cut along the outer edge of the interior door casings. Slice through any paint or old caulk.
3. Pry the side and head casings free using a hammer and flat bar.
4. Use a reciprocating saw fitted with a metal-cutting blade to slice through the nails holding the side and head jambs in place.
5. Pry the jambs out of the doorway opening.
6. Check to ensure that the threshold and side casings are level.
7. Fill the voids around the doorway opening with minimal-expansion insulating foam.
8. Apply a thick, continuous bead of acrylic-latex caulk along the threshold.
9. Set the pre-hung door into the opening, then tip it up and into place.
10. Center the door in the opening, then check the side jambs for plumb.
11. Secure the door by nailing through the exterior casings and into the jambs.
12. Tap out the hinge pins and remove the new door from its frame.
13. Pull out the weatherstripping along the side jambs.
14. Slip wood shims behind the side jamb on the hinge side of the doorframe. Then use a level to ensure the jamb is perfectly straight and not bowed in or out.
15. Shoot 2 1/2-inch nails through the jamb and shims into the house framing.
16. Drill screw-shank clearance holes through the jambs; position the holes where they’ll be hidden by the weatherstripping.
17. Drive 3-inch decking screws through the holes in the jambs and into the house framing.
18. Repeat Steps 13 through 17 to straighten and secure the latch-side jamb.
19. Cut the shims flush with the jambs using a utility knife.
20. Spray insulating foam into the voids around the doorjambs.
21. Fill any large voids with fiberglass insulation.
22. Reattach the weatherstripping to the jambs.
23. Nail new wood casing around the interior of the door.
24. Caulk the joints between the new doorframe and the exterior casing.
25. Apply an exterior-grade finish to both sides and all four edges of the wood door.
About Ask This Old House TV:
Homeowners have a virtual truckload of questions for us on smaller projects, and we’re ready to answer. Ask This Old House solves the steady stream of home improvement problems faced by our viewers—and we make house calls! Ask This Old House features some familiar faces from This Old House, including Kevin O’Connor, general contractor Tom Silva, plumbing and heating expert Richard Trethewey, and landscape contractor Roger Cook.
Follow This Old House and Ask This Old House:
Facebook: http://bit.ly/ThisOldHouseFB
Twitter: http://bit.ly/ThisOldHouseTwitter
http://bit.ly/AskTOHTwitter
Pinterest: http://bit.ly/ThisOldHousePinterest
Instagram: http://bit.ly/ThisOldHouseIG
http://bit.ly/AskTOHIG
Tumblr: http://bit.ly/ThisOldHouseTumblr
For more on This Old House and Ask This Old House, visit us at: http://bit.ly/ThisOldHouseWebsite
How to Install a Solid-Wood Exterior Door | Ask This Old House
https://www.youtube.com/user/thisoldhouse/
You must be logged in to post a comment.
This site uses Akismet to reduce spam. Learn how your comment data is processed.
I wish he could come to my house and do my front door
What a bunch of bullshit. Just get another door and hang it up. You didn't need to tear up all the trim. It's total bullshit.
Man, at 7:30 at the top right where the door meets the weatherstrip is a huge gap. That door is not right.
This old house Tom and Norm great show. Top notch master carpenters. They have forgotten more than most know!!
hay tom, tomas or tommy, what ever you prefer, just wander if you have any tips for buying a doorknob
First time He didn’t have festool drill why ?
This knocks out the lowes nonsense
Yeah, this video is based in reality.
I wish Tommy could visit my house. He would have a field day.
I actually change my own door after watching this video… Since I had an older door I ended up with a minor problem…. I have plaster walls and the new door is not flush to my walls.. I didn't realize the thickness of the door needs to be taken into consideration… I know next time.. But I still saved myself $400.00 dollars..