Kitchen

247 Videos

Order By: Title

Kitchen Remodel ~ Demo Day ~ Part 3

Beating on a dead horse will not make it run any better. To avoid any more wasted effort I decided to just cut out the middle part of the project and rip the stuff out. 😆😎 I think I have fixed the T Shirt problem. I signed up with TeeSpring to make and deliver Old…

web3d

12/11/2019

15.90K

Kitchen Remodel ~ Demo Day ~ Part 4 Fixing The Three Way

Kitchen Remodel ~ Demo Day ~ Pt 4 Fixing The 3 Way Published 11/13/2019 The cabinets in the way of the new range are gone. There is that little problem of the open wires on the 3 way switch. Guess I better fix that. Working on live wires can be done. I would rather not.…

web3d

13/11/2019

5.94K

Kitchen remodel: day 1, 2, 3. Demo & Installation. Issues discussion

We go through in order what was done on day 1,2,3. Issues the occur and what happened. Followup video: Problem occurs that delays our kitchen remodel - watch & learn https://youtu.be/QJy49Zw5w8E Welcome to RSmallHouz. We are going through a complete kitchen remodel with Lowe's. We will be updating you on each step along the way,…

web3d

07/01/2016

14.74K

Kitchen Remodel: Part 1.5 – Storage Cart for Stove

I felt the need to build a movable cart or dolly for our new stove, as we would not be ready to install the stove upon delivery. The cart is similar to other carts I have built, made from 4 pieces of 2x4 attached to form a rectangle. In building the cart I hold the…

web3d

14/04/2015

18.50K

Kitchen Remodel: Part 11 – Stove and Countertops

It was time to put the stove into position in the kitchen. The stove had been stored in the living room on a cart that I had made for it. I used a comment from Jon Wilson from the stove cart video to get to stove off the cart once we had it in the…

web3d

19/07/2015

1.16K

Kitchen Remodel: Part 12 – Bamboo Door and Drawer Fronts

I have made the door and drawer fronts to the kitchen cabinets from 3/4 inch bamboo plywood. One big advantage to this is that I did not need to cover the edges of the fronts, as the plywood is solid bamboo. Also, the plywood has a strong, linear grain pattern which I could use to…

web3d

01/08/2015

10.45K

Kitchen Remodel: Part 15: Breakfast Bar – Part A

I am finally getting back to the kitchen build - the last thing to finish is the breakfast bar. I had the support for the back splash behind the stove made before the counters went in. Now I will make a set of cubbies and a wood panel to cover the back of the stove.…

web3d

09/02/2016

Kitchen Remodel: Part 15: Breakfast Bar – Part B

I have built the bar top of the breakfast bar. It is made from khaya, a type of mahogany. The design idea for the bar is that the top surface wraps vertically at the end of the cabinetry, forming a miter at the transition. The grain runs continuously around the corner. To get the width…

web3d

26/02/2016

Kitchen Remodel: Part 15: Breakfast Bar – Part C

I have made the drawers for the breakfast bar. The boxes for the drawers are constructed in the same manner as the drawers in the rest of the kitchen. The side are held together with a tongue and groove joint with glue. The bottoms are held in a dado running around the bottom of the…

web3d

28/02/2016

Kitchen Remodel: Part 4 – Cabinet Carcass

I made the cabinet carcass from maple veneer plywood. I made the bottom pieces first to make sure they fit in the kitchen. The bottoms that are under the sections with drawers are frames to give me access to the base under the cabinets. I attached the pieces of the cabinets with glue, finish nails,…

web3d

16/05/2015

Kitchen Remodel: Part 5 – Drawers

I made the cabinet drawers from half inch birch plywood. I made the side pieces from some of the scraps leftover from the cabinets and two new sheets of plywood. I have three different heights of drawers wrapping around the kitchen. A deep drawer on the bottom, and medium drawer in the middle and a…

web3d

24/05/2015

3.22K

Kitchen Remodel: Part 8 – Cabinet Install

There was a lot more fitting and fussing with the cabinets to get them into place then I had originally thought. For the most part, these issues were all things I knew about, but had ignored until the last minute. I attached them down to the base and to each other with screws. They are…

web3d

20/06/2015

6.15K